Forums
-
OzFalcon
-
- 928
- posts
-
- By bear351c
-
- 9,338
- posts
-
- By SPArKy_Dave
-
- 1,136
- posts
-
- By bear351c
-
-
General
-
- 53,414
- posts
-
- By superyob
-
-
Merlin's Metalcraft Emporium
-
Panel Beating Tech
happy tappy...
- 264
- posts
-
- By dvfalcon
-
- 75
- posts
-
- By Fingers
-
-
Technical
-
- 16,614
- posts
-
- 9,815
- posts
-
- 1,018
- posts
-
- 774
- posts
-
- 4,235
- posts
-
- 4,717
- posts
-
- 3,887
- posts
-
- 292
- posts
-
- 2,466
- posts
-
- 4,016
- posts
-
- 632
- posts
-
- 3,030
- posts
-
- 263
- posts
-
- 1,454
- posts
-
-
Projects
-
- 9,084
- posts
-
- By judgetread
-
- 92,931
- posts
-
- By CHESTNUTXE
-
- 4,809
- posts
-
- By Hawksam67
-
- 1,060
- posts
-
- By Squiz
-
-
Trash 'n' Treasure
-
- 1,391
- posts
-
- By CHESTNUTXE
-
- 3,713
- posts
-
- By motoSycho
-
- 1
- post
-
- By 'Nova
-
- 2,348
- posts
-
- By adrianphu123
-
-
EA to FG Q&A or general info
-
- 35
- posts
-
-
Forum Statistics
7,939
Total Topics274,933
Total Posts -
Member Statistics
-
Who's Online 2 Members, 0 Anonymous, 169 Guests (See full list)
-
Topics
-
-
Posts
-
So the variable resistor in my ZD's headlight switch has clapped out. I bought a switch from rare spares and the dash lights are very dim at best. Is there a way to bypass the resistor on my original switch? Preferably without starting a fire behind my dash...
-
Id go for a GT35 as they come on boost instantly on a 250 anyway.Convert to a 4 barrel set up as your about to jam it full of air. A 2 barrel is too small on a 200 engine let alone a 250. Id measure compression first before lowering it and if it's around 10.1 leave it alone or your making it a laggy by lowering compression for no reason. I know you don't want to make a million hp but your actually treating it better if you let it become more efficient. Upside you don't need to push it as hard to get the results you want. Id fit a programable ignition too. EST dizzy and ecu or maf control. Then you can run 28 plus degrees @ idle and low RPM no boost then drop timing as boost comes on. -
-
Thanks mate. Thats what i was hoping. Do you think a 275 will fit? -
Holy what a blast from the past, forgot all about this forum. From memory 15x10s with a 5” backspace fitted quite nicely.
-
Hi Mate. Howd you go with the 15X10s? we are getting a xw gt replica and want to know the biggest tyres you have been able to fit without scrubbing. We have some 15x10 centerlines that where going on our p6. pretty sure 5"backspace.
-
XB style knob might be similar to something from a celica from the 1970s with the same pattern as a T5 (different thread, but could be tapped possibly?) the XG clutch plate might fit in the 3 speed pressure plate, i can't remember if the T5 pressure plate will have 3 or 6 bolts.. if it's 3 bolt it will bolt on, and if it's 6 bolt, it might still bolt on. but ideally you'd drill more holes.
the hole for the shifter is basically dictated by the hump, it fits the floor/tunnel snug, trace around it.. leaving a fair edge around the sides, and put the hump further back than snug forward (when i fitted a T5 to My XE the hump was rubbing on the shifter housing initially.. i just removed the hump screws, and set it back 5mm ish, drilled new holes.. and hammerd the floor a bit more at the back)
The XG hump is spot welded onto the floor, you should be able to use it in the same way, but it's bulkier from memory. -
Been speaking with the mechanic whonis doing the conversion for me, He's pretty certain it'll be an easy swap over using the old 3 speed bellhousing and clutch assembly. The main thing he's concerned about is cutting a hole in the floor, thank christ all the parts for that are now easily available as repro's....not cheap but a whole lot easier than trying to find 50 year old parts at a wreckers or online somewhere. If only the was an XB style gearshift knob with the T5 layout printed on it...🤣 -
What sort of manifold did you use? I've heard about fuel pooling issues with manifolds that have smallish plennum areas. I was thinking of using the 2300 2bbl unit on my 250 2v and upgrade the manifold to an aussiespeed one with a larger plennum than the factory manifold I current have. From what I have seen on Holleys website the 2300 should support up to 650hp boosted...hopefully that isnt a misprint, wayyyy more than I need but nice to have the extra capacity...lol
-
Just used a sniper on 427 small block , blow thru with a Vortec V7 . Using the Sniper is a great setup for fuelling, almost too easy
-
