Mustardxf2
Members-
Content Count
260 -
Joined
-
Last visited
About Mustardxf2
-
Rank
Advanced Member
Recent Profile Visitors
1,671 profile views
-
S-Pac Jake reacted to a post in a topic: Xf EST issues
-
Next time it does it have a spare coil on hand to swap out and see if that fixes it, if not do test to see if if distributor is putting a spark signal out and or getting spark when cranking Sent from my iPhone using Tapatalk
-
deankxf reacted to a post in a topic: Xf EST issues
-
I hunted this problem for months when I had it happen swapped coils multiple times and was deadset a small crack in the dizzy body that I found when I was swapping it out Sent from my iPhone using Tapatalk
-
Mustardxf2 started following Crossflow Harmonic balancer bolt undoing itself , Xf EST issues, XF crossflow flywheel and and 1 other
-
Hey mate I had similar problems once upon a time, car would be fine drive fine do everything thing it should but would shut off randomly turning corners, and then would not start until it was cooled down. Check and inspect your distributor cap, rotor button and the plastic case the rotor button rotates on for any small cracks. I pulled mine and found a small crack that was opening up once hot and swapped it out and never had an issue again. Sent from my iPhone using Tapatalk
-
This is the package I just got from NPC Sent from my iPhone using Tapatalk
-
RNF44 is the flywheel part number, you’ll need to make them aware that it will Be bolting to a crossflow. Sent from my iPhone using Tapatalk
-
NPC do a lightened flywheel for the crossflow, which I believe is a 4l flywheel drilled to suit crossflow, accepts 10.5” clutch with 6 bolt pattern and dowels instead of 3 bolts. Sent from my iPhone using Tapatalk
-
Im after some information on modifying standard rubber mounts to be abit more durable, I've heard of putting a bolt through the middle, can anyone elaborate? Sent from my Pixel XL using Tapatalk
-
Crossflow Harmonic balancer bolt undoing itself
Mustardxf2 replied to Mustardxf2's topic in Crossflow
Yeah definitely going back to the builder second time now even after its second rebuild and I don't want to fuck it it again because I'm not building in for the 3rd time aha Sent from my Pixel XL using Tapatalk -
Crossflow Harmonic balancer bolt undoing itself
Mustardxf2 replied to Mustardxf2's topic in Crossflow
Yeah will try the loctite Sent from my Pixel XL using Tapatalk -
Crossflow Harmonic balancer bolt undoing itself
Mustardxf2 replied to Mustardxf2's topic in Crossflow
That's what happen the first time it was built but the harmonic balancer had a crack in it and chewed both ends on the crank out. Going to go see the engine builder to cover my ass incase there is something else wrong again. Sent from my Pixel XL using Tapatalk -
Crossflow Harmonic balancer bolt undoing itself
Mustardxf2 replied to Mustardxf2's topic in Crossflow
Yeah that's what I'm going to do, just didn't know wether it was common or I'm the only one. Sent from my Pixel XL using Tapatalk -
Has anyone had a problem with the bolt backing out? Motor has been reassembled twice and has happened both times! Sent from my Pixel XL using Tapatalk
-
Xg one, but running it east west I believe a standard crossflow one would be long enough since it's the same throttle configuration as the Weber Sent from my Pixel XL using Tapatalk
-
Buy a bracket and find out, I will have to trim mine about half an inch to not stall on the rocker cover, the with 2" apacer. Sent from my Pixel XL using Tapatalk
-
Thanks for that, will revert to this plan if current setup does not work, I pinched the 12volt ignition from the second washer bottle pump plug, hopefully this works was nice and easy and isn't powering anything else Sent from my Pixel XL using Tapatalk