wokko

Just an update, I had to wait for the weather to clear up (no luxury garage ), I pulled the rad and then balancer/timing cover off and realigned to tdc which the mark on the pulley was about 30 mm out so outback jack was correct around 12 o'clock was good
I put it all back togther with new timing cover gasket/seal and said a few hell marys and turn the key and it purred like a cat
warmed it up and put it into timing mode which took a few goes (knew something was going to go wrong it was going too well )
Set it to 5deg and through some 98 fuel it it and it is like a new motor.
Cheers and thank you fro everyones help

Just an update, I had to wait for the weather to clear up (no luxury garage ), I pulled the rad and then balancer/timing cover off and realigned to tdc which the mark on the pulley was about 30 mm out so outback jack was correct around 12 o'clock was good
I put it all back togther with new timing cover gasket/seal and said a few hell marys and turn the key and it purred like a cat
warmed it up and put it into timing mode which took a few goes (knew something was going to go wrong it was going too well )
Set it to 5deg and through some 98 fuel it it and it is like a new motor.
Cheers and thank you fro everyones help

It doesn't want to run probably I think I will pull timing cover /harmonic balancer off and realign and remark the balancer as I don't think that mark is correct ?
that pcv valve is no good and waiting for one to come in the mail this week

Kool thank you Lets see how that goes :)
Those muppets are making life hard :)

Yeah ecu has 2DMA
Got pic but exceed my limit of uploads

Cheers for the help and pics, this is my motor I think that timing case looks like a ef/el one ?

I'm not sure what I doing wrong but does this look right ?

 

Hey guys, has anyone got a pdf or link to
Ford Falcon XG Ute & Van 1993 Repair Manual Supplement
cheers
or even a pic of how the dizzy is fitted.

There is only one mark on my timing case which is a v looking plate with a line in the middle and no other markings.
There is also no mark on the harmonic balancer either, well one small mark on the inside which seems to be it ???
So I'm assuming now that (timing mark plate thingy)  maybe the 10 deg mark
Hopefully tomorrow If the treat it as the 10 deg btdc I might be ok ???
Thanks for tfi info as I wasn't sure where to have it pointing.

Cheers mate I was doing that but the car wont start. only thing I'm not sure of is there is a metal ( V looking) plate coming of the timing cover with a line down the middle but I'm not sure if that is the 0 mark or 10 deg mark as there is nothing on it to say and maybe that's my issue as I'm lining it up with that mark ???
I did know about bridging those ports but need to be able to start it first probably :)

Yes it had a sock on it albeit dirty but was there,
It started fine but it was rough as guts and the sounded like the timing was out of whack.
Last owner apparently put a new dizzy in it but couldn't get it going which ended up being a fuel relay instead.
So I thought I redo the dizzy and redo the timing but what a nightmare
I set it like the falcon manual says and car wont start at all
I need to point the rotor at nearly 9 o'clock before it will even start but very rough and smell the richness of fuel
So I must be doing something wrong
The way the manual has the tfi module and rotor just does not work for for some reason
Oh yeah I will replace that donut looking thing I was lazy and left it on
 
 
 

I brought a Fuelmiser fuel pump today and fitted it.
It started fine but running/idling rough as guts.
I did put a new fuel filter on it a couple of weeks ago, wondering if I should get another one or just pull it off and check it first ???
I need to pull the fuel pump out again  as the sender unit is reading a 1/4 more than it should ( I can't win with this ute )
But atleast it is running.

Cheers will look at them tomorrow
The pump is very noisy, its been like that since I brought the ute
I thought it was just like that in the falcon utes as I haven't owmed a ute (vh dodge ute) for around 20 or so years and couldn't remember if they were noisy or not

I have a 1993 xg falcon ute 4 liter
I went for a cruise today as I had some stutter issues on acceleration which I tracked down to a crack in the hose of the map sensor on the manifold side.
Car run beautiful until the way home, it died.... turn key and it has a weak prime sound and then the pump stops, prior to this when you start the car you can hear the pump running all the time.
Do you think the fuel pump has died?

Just an update
pulled water pump off as it was leaking
full of silicon as a gasket and O ring for return heater pipe
Not sure what people are thinking, all that time ripping off belts,fan and water pump albeit draining fluid (dirty/greasy job) and can't go down and spent $8 from repco/supercheap for a gasket/O ring

But all is well it has a brand new water pump and I have a spare one if I get another falcon.  

Cheers Guys
all sorted, came off quite easy with a longer spanner
did find a broken 10 mm bolt on water pump pulley so glad I did this
 

there's not complete pics in here(i used someone elses at the time)
 
 

Kool, thank you
I'll give it a go tonight if I get home before it gets dark otherwise tomorrow.

I've always gone to great lengths to obtain and use only OEM/name brand replacement fuses.
(much to the amusement of others)
 
Recently, I stumbled across a youtube clip, which clearly illustrates the reasons why.
NEVER use cheap fuses...
 
Some aftermarket offerings are so 'out of spec', that their TRUE rating is closer to x5 times higher.
ie - marked as 10amp, but ACTUALLY rated at 40amps
 
For those who value their vehicles, I'd strongly suggest to watch -
 
 

All is well now as diagram from diagram 21-3-5 shows connector pin loctions

Yeah all clip on fine and got 8mm bosch leads, there were 10mm bosch leads that i was going to grab but original  ones were  8mm so went with them
packed up for the day, will have a look tomorrow.
I think I will  pull no 1 spark plug and spin crank to tdc and check rotor to verify all is good with dizy/cap.
I know there is someone silly I've done somewhere which I'll find one day 😆

Probably was the relay, I'll test another one tomorrow to see what the go is, but it does seem strange both the ea and xg relays did the same on both cars, not connected to fender and no prime, connect to fender and it primes.... possibly a X-file :)

ended up being bad wiring (fuel pump)