-
Content Count
377 -
Joined
-
Last visited
-
Days Won
1
Content Type
Profiles
Forums
Calendar
Everything posted by dvfalcon
-
XF 5spd ain’t much chop, came with the 3.3, from memory same as a sigma. Better off with a 4 Spd. Hunt up a e-series 6 cylinder. This is a bell housing I modded a singlerail bel housing the bottom two are the new
-
Wiper relay in? LHS of steering column
- 6 replies
-
- electrical
- demist
-
(and 2 more)
Tagged with:
-
Top work have been following this build
-
Sent from my iPad using Tapatalk
-
Put it back as it left the factory
-
It does support the top plenum cover couple of spot welds, directly below there is the pedal box. There is bolts on that area for the wiper motor assembly isn’t there? Support Just going of memory car to far away atm.
-
Electrifying a Gasoline engine (converting an ICE to plugin hybrid)
dvfalcon replied to nullyoaG's topic in LPG Tech
Photo stolen from Facebook, one in the build Sent from my iPad using Tapatalk -
WARNING - Ultra King shock absorbers = DANGER!
dvfalcon replied to SPArKy_Dave's topic in Steering, Suspension and Brakes
I have used him good price and service -
Tips on welding cracked strut tower in XG ute
dvfalcon replied to JohnnyeHCF's topic in Body and Exterior
I killed one of my Xe’s Cracking between the upper control. All caused by a new set of tyres and a crap wheel alignment. Every so often would grabbed the front guard. Didn’t fix scraped it my bad. if you have the time replace as much as you can with doner parts. A few layers make up this area, and it cops a pounding Dale -
XE Falcon Spac stripes/decals and front lip spoiler
dvfalcon replied to wok's topic in Body and Exterior
As Sparky Dave said http://grafixunlimited.com.au/ford/falcon/xd_xe_xf_zj_zk_zl/xe -
Manual transmission builders in Vic
dvfalcon replied to scottly's topic in Transmission and Differential
Single rails are good, stop the gear stick from coming out, the only issue you will have is the selector rail seal. Dale -
As sparky Dave said, the xf plugs were once available off the shelf at Autobarn been a while since I bought them. Jay Dee auto cables in Baywater sold them as well Dale
-
Just a question as some times alternative oils run better than what leaves the factory. What oil grade should I be useing in a T5. It was originally out of Ed I was told going behind a cleveland thanks in advance. Dals
-
Just for those after the gear stick for the floor. Had trouble sourcing a XE so I ended up at the GT SHOP. To see what the has and if I could use it, the had repo ones for a XC that worked a treat Sent from my iPhone using Tapatalk
-
This guys I will start chasing one down
-
Thanks for your help all gear box is in and it moves car not finished enough to drive. Just another question. What floor gear stick boot should I use. T5 in a Xe. thanks Dale
-
Thanks every one for there input, I will start with dex111 and. See how it shifts and then add a additive if required
-
Thanks Dean what additive/ what is the additive for Dale
-
Hard to explain and to hard on the run to draw and post a picture on the run but as you suggested I would run a new wire and join it at the cluster plug and see how he goes.
-
deankdx The oil sender works resistance to ground.the ground is though the body of the sender as resistance changes oil pressure gauge changes. This being the case the wire should run from the sender to the cluster with no interference from supply or earth “””””With it unplugged at both ends, cluster check if it has +12v there( shorted to 12v).”””””””” cluster un plugged and. Wire off the oil sender depending if multi meter or just a test lamp I would check if +12v is being introduced in to the wire, wire is shorted to +12 volt Multimeter - place the black lead to earth and the red lead on the wire, if you measure 12v the the wire is shorted to +12volt. test lamp - connect the clip on the lead to earth and touch the probe on the wire, if it lights up the wire is shorted to +12v “”””””Check if is grounded to -12v (shorted to Earth)””””” Multimeter - place the red lead to +12v and the black lead to the wire, if you measure voltage the wire it is shorted to the earth. testlamp - connect the clip on the lead to the wire and and the the probe to +12v, if it lights up the wire is shorted to earth.
-
Just keep in mind Xd Xe have oil senders. And some dash looms have less wires(budget/basic loom) have done many dash changes, instrument panel with no issues only ever had one loom that did’t have all the loom wires. Do a resistance check from the from the sender to the to dash plug. With it unplugged at both ends, cluster check if it has +12v there( shorted to 12v). Check if is grounded to -12v (shorted to Earth)
-
Did these come in f100’s
-
The top original handle in your first photo the plastic clip that holds the rod on is from a xf (rod has a90degreee bend in it. Xd/Xe rod had a S shape bend in it and goes through the eyelet grommet that came that came on the new one. I would say the hole drilled in the new arm is to large for the xf attachment. You could always make up anew rod but I would just repair you old one
-
Is it legal to remove the heavy bar in the xf rear bumper?
dvfalcon replied to GRIFF's topic in Body and Exterior
This if just the factory toe bar. The hardest part would be finding standard bumper irons