Hofiveo
-
Content Count
121 -
Joined
-
Last visited
Posts posted by Hofiveo
-
-
Reviving from the dead for good reason, have a look at this shops setup. Not a carby but check out what he's done on the ignition side of things!
Pics not working or is it just me.
-
-
First thing I thought it might be was coil pack so I put a new one in as well as plugs and leads as it did have a slight misfire.
-
Any au falcon guru's here familiar with the engine cutting out with out warning on hot day's. Had my mate's scan tool on it and no fault codes come up. I've read that it could be the crank angle sensor and they don't throw a fault code when it happens. It's only done it on real warm days and will restart if left to cool for a bit. Anyway just wondering if anyone here has had the same problem.
-
Anyone using the street terra st2003 rollers. Suppose to suit clevo and big block chev. 1.72 ratio and 7/16 stud.
I've read some stuff on people using chev rockers on clevo's and I've read some stuff about clevo roller rockers being specifically for Clevelands. So I'm wondering why yella terra make a one size fits both. Anyone have first hand experience with these.
-
You can get a single pak spot primer in a spay bomb for rub throughs and fry ups. Says it's suitable under two pack systems as well. Ive used it under two pac and no problems so far. 2 pack primer would be better and seems to work fine on small areas of bare steel.
scottly reacted to this -
Yeah. Just found them. Cheers. Didn't think they were that expensive.!!
Yeah there pretty pricey. I'm sure I've seen them advertised somewhere else as well. Might have been in street machine magazine.
-
-
If you can move the recirculation flap by hand with no resistance then that will be the problem.
Ando81 reacted to this -
Perfect example right there. Glue and laminate.
-
Is it this doohickie that Mr polson was talking about.???
http://www.ozfalcon.com.au/index.php?/topic/3553-where-is-this-cold-air-coming-from/
That's the one. Xf control valve has two vac lines and xe has one. The box and flap are the same. The little black lever that the control arm connects to snaps.
bear351c reacted to this -
Is it this doohickie that Mr polson was talking about.???
http://www.ozfalcon.com.au/index.php?/topic/3553-where-is-this-cold-air-coming-from/
That's the one. The little black arm the control arm connects to snaps. Xf vac control have two vac lines and xe have one but the box and flap are the same.
-
Hmmmm, is it the flap that is behind the glove box? I watched mine slowly open and close but it seemed sluggish. I could see the whole lever coming from the actuator and there isn't any broken pieces. Will be busy for a couple of days so I might have to get back to it later in the week.
That's the one. The flap has a foam seal normally but it will be crumbly and long gone by now. Could be a vac leak somewhere. Some Xf's had an xtra vac canister in the front plenum and some don't. Check the rubber boot that connects the hard nylon vac line to the motor because they split and leak.
Ando81 reacted to this -
Try and find one that's not broken or glue back together with rapid fix and a little piece of sheet metal to reinforce it. That's what I did anyway.
-
Cold air in the passanger side foot well will be a broken fresh air recirculate arm on the vac controller. Bastard things are a broken more often than not from my experience with xd xe xf's. Dash out job to fix it to.
bear351c reacted to this -
CVF racing do a kit for clevo called the beast. It's an 8 rib belt from memory. Look on eBay.
-
Got mine done a few years back in grey velour. Gave them my old one as a pattern and picked up the new one. Fitted it myself. Cost 200 bucks from memory.
Outback Jack reacted to this -
I think your right. Bigger than 2v and smaller than a 4v. I did read something about it somewhere but don't recall the exact specs.
-
Isn't the Scott Cook manifold more of a 4v design than a 2v.
-
My first xe had a 2.53:1
Great for highway bad for getup and go.
gerg and n00bus m@x1mus reacted to this -
Any updates yet. Keen to see how your going with them.
-
-
Sounds like she'll be a sweet combo mate. Are you able to share any secrets about the killa valve job.
-
What happened to the lunati cam.
converting a barra to carb
in 6 Cylinder Tech
Posted
That's a flash bit of gear there.