-
Content Count
124 -
Joined
-
Last visited
Posts posted by ```
-
-
13 hours ago, Valvebouncer said:Weird. Has someone cut a hole in them?
I some times look at them and think that they probably have been cut!
Valvebouncer reacted to this -
Can anybody tell me what these come from?
They came with a set of ROH 12 slots I bought 5 years ago but can't seem to find anything like them on the internet.
I thought I had seen some similar with GT badges in the centre?..I may be totally wrong!
-
11 hours ago, Mr Polson said:12 hours ago, ``` said:What are the Fuelmiser pumps like?
Does anyone make replacement in tank sender units for the xd?Fuelmiser is just a box, they don't make anything. They buy other companies parts and put them in a Fuelmiser box, so you could end up with a cheaper no name part, or something made by someone like VDO
Do VDO still make them?
-
What are the Fuelmiser pumps like?
Does anyone make replacement in tank sender units for the xd?
-
17 hours ago, bear351c said:says your vid is private.
bugger..didn't realise it was set as private!
have sorted it now.
When I removed it from the car it still had fuel in it and I could pump fuel out of it so assume it is ok?
-
anybody else having trouble viewing it?
I have re-posted and hopefully it works now (works for me by the way)
-
Can anybody tell me how much movement there should be on a mechanical fuel pump?
The one on my sons 81 xd 4.1 looks like it is the original and I am not sure if it's working properly.
The video shows how much movement there is of the 'arm'..just not sure if it should more or if it looks right?
cheers.
bear351c reacted to this -
-
34 minutes ago, deankdx said:video not working,
but the stock engine bay looks better to Me!try this
bear351c and deankxf reacted to this -
Delay in getting this sorted was also due to stripping and repainting the original rocker covers and air cleaner
Before:
After:
And a short video of it running..seems to be running pretty good..no backfires or spluttering..just need to take it for a little spin to see how it goes out on the road.
-
17 hours ago, ESPSIX said:Sure, just make sure the flap inside the snorkel is in the cold air position.
I assume that is with the flap closed against the hole?
-
5 minutes ago, ESPSIX said:although, non of these things are needed unless you are hooking up all the emission gear.
and the one your looking for just helps warm the motor up quicker, by getting it to suck hot air off the exhaust manifold.
So I can happily run the stock air cleaner including the snorkel without it?
-
2 minutes ago, bear351c said:Is that your engine bay? It looks MINT.!
Shit..I wish it was!!
belongs to this guy
http://www.xfalcon.com/forums/index.php?/topic/5616-feb-82-xd-ex-pursuit/
-
This is the hose I am talking about..so it goes from the left hand rocker cover to the carb? (obviously this is a Carter and not a Holley)
I haven't got the PCV valve that fits in the grommit..would this one be suitable?
I also need the vacuum switch(?) that fits between the snorkel and the base of the air cleaner
will one from a 6cyl air cleaner be suitable?
-
Actually really pleased how the air cleaner and rocker covers have come up..and all with rattle cans of VHT Argent Silver!
I will post some more before and after pic's.
-
2 minutes ago, bear351c said:Don't forget, the XD air cleaner is silver, and the snorkel sits upright/vertical. Unlike the XA/XB which sits horizontal.
Before..
After!
SLO247, Outback Jack and bear351c reacted to this -
I am putting back on to my car the original V8 air cleaner.
It is going onto a Holley carb and Weiand intake manifold until I can get the Carter and stock manifold setup on there.
Now..where would the breather pipe on the left (drivers side) rocker cover go to?
I know the right hand one goes to the filler cap and air cleaner body but not sure on the other one,
cheers.
-
2 hours ago, Outback Jack said:I dunno whats taking so long.
work and other stuff!
Outback Jack reacted to this -
On 10/20/2017 at 5:26 PM, bear351c said:For absolute check, pop off the left hand rocker cover and see if the valves are up or down, pushrods should spin with 2 fingers.
Still faffing about with this
Which pushrods are you referring to..just the front two?
bear351c reacted to this -
Ok..managed to get the dizzy spikes lined up and have relocated the plug leads to correspond.
Will have to give it a crank over in the morning as the other half is in bed as she works nights and will not be popular if I wake her up!!
-
14 hours ago, bear351c said:then 'spiky wheel' in the dizzy should be lined up with one of the spikes on the outer ring.
So this is how I had it set up but, as I say, had to turn the dizzy as far clockwise as I could and vacuum ended up at 7 o'clock ish.
If I am understanding you right, I need to lift the dizzy out enough to rotate it (anti-clockwise?) and line the two sets of spiky wheels up then set the new position of the rotor arm to no.1 plug lead and the rest to follow?
bear351c reacted to this -
If I am having to turn the dizzy all as far as is possible clockwise to get it anywhere near running right is the dizzy in the wrong place?
To my untrained brain I am thinking it may be a notch out of alignment..if that's correct, which way do I turn one notch, clockwise or anti-clockwise?
First pic is of it turned as far as it can go (vacuum at roughly 7 0'clock) and second one is of it with the vacuum pointing to the front (roughly 6 o'clock).
-
I have a few different ones kicking around spare so will grab some and give them a try.
I think one of the starter motor bolts also holds the inspection plate on so might remove that and try it in the holes (ooer!)
-
1 hour ago, bear351c said:Think they're 1/4" UNC. About 3/4" inch long. Try a rocker cover bolt, (same) Definitely UNC.
ok..just tried the rocker cover bolts and they just pushed in so are too small
12 slot centre caps?
in Wheels and Tyres
Posted
sounds plausible.