tpak addict

This the kinda thing that can drive you loopy.... My ZL was 10k under and chucked in another transducer and its now 9k over with the same cog... Now I just spped everywhere lol Sent from my GT-I9300 using Tapatalk

I thought the only physical difference was the shifter was on the other side....

just realise you are talking about a ghia.... I have done it before with a Falcon tho (grey dash to black) Yes looks like you are up for a full loom change.... oh that sounds like fun....

you can just do the dash convert using Series 1 wiring. will have to extend a couple wires or cut chop plugs off the series 2 loom....

You could become the Peter Anderson of OzFalcon!!

haha I remember the good ol days.... Need a mirror for a XD.... $10... got one on the shelf.....

Lets face it we Fairmont and Fairlane owners have seen this and it makes the car look like crap..... It brings the whole look of the car down... So here is a cheap easy solution thanks to the interwebs and little dollars... So hit up good ol' ebay and get some 9mm chrome tape (perfect size) but you can get 12mm if none is available... Should set you back a whopping $10 or so including shipping,,,, May take up to 4 weeks if from china,,,,, What you need is.... Your chrome tape. A nice sharp knife,,,, Wax & grease remover.... Now sit on ya bum and get your knife..... Slide along the top and lower edge of the chrome strip on the car with the knife. When you have done that a few times. Peel away the chrome strip. you should have just a greyish looking bit underneath. Clean off with the wax and grease remover. Let area dry. Get your chrome tape and place level with lower edge and just rub around 1cm on one end. Pull the tape with medium pressure and line up to other end and run finger across the strip.. cut off end (roughly ok at this point_ Now run finger over the chrome strip and make sure it is all down and run finger nail on top and bottom to get the chrome strip to get it right in there (you can grow your finger nails while you are waiting for chrome tape to arrive). Then trim off excess.... Tada..... Dont like chrome? Your choice of colour, after all its only pinstripe.... This will last a while but may need to do every couple years if you want it to look at its best. But its only $10 and a hour of your time (depending on how many you need to do)....

Its cheap and effective... and unless you look closely you cant tell.... For little money it makes a world of difference... Time I have, Money not so much of....

or could go EA2 ecu (no smartlock) and engine loom

if you want to try another AFM I have a spare one if you want to check if its that....

I like Hurricanes\ suit XD's up to a T

Old School rims on a old school car for the win personally..... Dont like the modern wheels on old cars... Just looks wrong. Just not enough dish. Grab some EF 15's for now and spend some time over the next few months on gumtree, something will turn up.... Thats how I got mine and what a bargain it was too..... Rims for $200.... New tyres all round $450 Surprised Hendix hasnt tried to steal them.... lol

What about a T700.... arent these a 4 speed version of a T400 with cable kickdown (no electrics)

If anyone would know its Phantom... When it comes to ford stuff he knows, may pay you to send him a PM if you want to know for sure.....

Thom is on the money, quickest and easiest way to check..... Not all XR diff's are LSD. It was an option same as all models even the egas.....

Dizzies will turn a little as you slide them in.....

Thats why you always put it on number 1 tdc before you pull the dizzy out..... There should be a small notch on the dizzy that lines up to number 1. rotor will line up with it when its in correct spot.

0 is top dead centre number 1 cylinder

get one that you are happy with.....

What you need is a mate..... Remove number 1 plug.... Get said mate to stick his finger in the hole...... of number 1 turn engine over by hand.... Very important when on comression stroke should hear a hiss emitting from said finger line up timing mark to number 1 on pulley

Hahaha yeah I remember way back when I was a lad doing donuts in the HK I could get it to do perfect circles on dirt (one front wheel staying in the one spot). HQ just couldnt do that..... I remember a mate having a HQ with a 350 and it would go sideways in a straight line doing a burnout, that was kinda cool tho....

Just remember tho.... Change ECU or BEM and its a tow truck to the place to get it programmed.....

ECU & BEM in BA+ need to be programmed for the car to start..... Even the Radio/CD needs to be programmed There are some places that can do this besides Ford

If its a small area I use buffing compound by hand.....

Hmmmm EA-AU exhausts are plentiful down at U-Pullit and get the odd 2.5"too.... I have a MIG...... Might have to invest in a pipe cutter I thinks......