gregaust
-
Content Count
343 -
Joined
-
Last visited
Posts posted by gregaust
-
-
Whoops just reread realized was XE not XF
-
-
Something is not right in that caliper . That lever should be downwards . If it is the original lever there could be an assembly issue .
The reason I say original lever is from memory there was a couple different levers . That type with a single loop on the end from memory was XD
The XC levers had like a double section where the cable attaches
bear351c reacted to this -
Near on 100 bucks for a thermostat ? There's been so much talk of Clevo specific thermostats like these of late . For many years no one bothered or even heard of this and didn't have issues .. Sure seems like a social media following to fix other issues ?????
Opening up for discussion
SPArKy_Dave and bear351c reacted to this -
I will add . I don't get the whole Wilwood thing . I did a setup for a guy on an XA to fit up to the factory stub axles . The rotors were very thin and to me appeared flimsy . The calipers were smaller than the later model Ford ones ..
gerg reacted to this -
Good topic . I've been experimenting using all factory stuff .
Started with XC disc/hub unit
Cut the rotor off
machine the hub ( that is originally around 20mm thick) to allow for added thickness of rotor
I didn't finish my setup but a mate has and he used calipers from a territory and rotors , I think his were 322mm
Once hub is machined you need to leave the centre hub a little oversize than the wheel centre part to locate the rotor
The caliper bolts up to the XC factory lower hole on the stub axle
Machine a spacer to centre caliper
A top mount block needs to be made up from original stub axle hole to caliper
Anyway his all came up good and is running. He did do some pics on FordForums.com.au
My setup I was using all FG calipers etc and 322 mm rotors . I had some interference between the rotor O.D and caliper but his with the territory gear worked .
-
Yep you got it for the worm adjuster . It is adjusted carefully on the bench so preload is slightly firmer at centre .
If you like I can measure up the tool I have for that seal . Basically it is exact O.D of the seal , then has a large land at the bottom of the case so as to guide the seal in dead straight. The seal is tapped in very careful so it just touches the very small step in the case
The seal expanders I made up out of exhaust tube years ago , basically tapered enough to expand them over the lands where they fit . Then there is a tapered sleeve bit like a ring compressor that is the bore size the Teflon seal runs in. That shrinks the seal after being fitted a while so they slip easy into place
gerg reacted to this -
A link to the roller conversion? The top bushes are always worn. I bought up quite a few roller covers many years ago when they were available . Apparently the company that made them would only do batches of 5000. None are available now . From memory the bearing is the same as the lower sector shaft bearings . I have a few of those . But there was also a washer machined into the top cover to control the sector shaft endfloat .
Been considering modifying a few stock bushed covers
-
Ouch . They are not an easy thing to just put a seal kit through. To do properly is quite few special tools . The tools are to expand the Teflon seals to fit , then sleeves to reduce them to the bore size so they go in. The tricky part is the input seal . It has to go in from the inside and the tool required presses the seal in from the bottom. That seal is easily damaged plus there is only a very fine lip to press it to so be careful
Then setting up the preloads on assembly is very important
gerg reacted to this -
As long as there is some oil in converter it will be fine . From memory you said it was a runner. If so i'd not fill it will soon fill as soon as it is started .
As for shifter , there are many different levers on a C6 at the case . All depends what you have , it can be tricky to get a factory shifter to line up exactly to the shifter detents .
Not impossible but takes some work .
The American shifter setup aren't too bad . At least you'd know it will line up right .
Those HP figures are a joke . Someone came up with them years ago and honestly they are laughable .
Seriously if someone lost a second with a gearbox swap they need more power lol
-
10 hours ago, CHESTNUTXE said:So what is the go when trying to find the correct Speedo gear for say 2.92 ? The black spiral thing is the big gear i guess ? I also managed to get the navy seal out
Sent from my SM-G570Y using Tapatalk
No that black rubber seal is for the yoke . Depends on the yoke you use it's likely not needed .
The speedo runs further forward . Speedo gear is same as what a C4 would be
CHESTNUTXE reacted to this -
Speedo will go right in . Just be sure to use the correct gear
L servo is an ok one to use
Does look very clean , depends on you use a shift kit may be a good addition. A stock C6 shifts soft
CHESTNUTXE reacted to this -
Looking where it is located , possibly stability for the brake booster area ??
gerg and deankxf reacted to this -
With 3.5's depending on tyre diameter usually I go with 20 or 21 gets it near spot on
Thom and bear351c reacted to this -
-
Did you guys ever get any further on this . A mate is doing one now . A BTR V8 trans and converter bolted right up to a Clevo flexplate . Yet to have it driving , but using the early stand alone ECU. Looks to be so far a good swap
The guy previously had an AOD that would die every few weeks . It'd been rebuilt and modded several times I believe but obviously not done right
gerg reacted to this -
If the head gasket is wrong it'd be blowing coolant out the radiator in less than 10 mins
-
On 3/7/2019 at 2:56 PM, Travis said:
Is there a way to check if the gasket is on wrong without pulling the heads off?
Sent from my iPhone using TapatalkYes you can . If you look at a gasket , the front and rear corners are different. The front corner is more square , you square see that square bit exposed . The rear corner tapers off
gerg reacted to this -
Sure it's not pinging??
Lash @ .020" . Is it a solid cam?
-
21 hours ago, XFtoXE said:Quick question. Does a brake booster VH356 off a XC fit a XE?
Any answers appreciated.
Yes same have done it also
-
Big Block will go in early cars ok . Castle auto pipes go right in they are tight out of the heads but make way more torque than any small block ever will.
CHESTNUTXE reacted to this -
Following, i need a rebuild kit also
-
Good result . So the old hose was blocked once you removed it ???
-
2 minutes ago, deankdx said:i've had this a few times now as i've had 30 odd year old cars now quite often.. the hose ruptures internally
Yes I've had a few too. I had an XC hose , no matter what I did even with over 100 psi air it was solid
deankxf and Outback Jack reacted to this
CLEVELAND ENGINE TALK
in Cleveland
Posted
Just one tip. That carb gasket , cut it to match the oval plate . I have seen those pieces get sucked away