Outback Jack

I'd just leave the 4L on the front of the T5 and be done with it..... hehe... Good excuse for an Upgrade.

Jack.

I know it sounds stupid, but check for a vaccuum leak, I spent a fortune on new brakes, master cylinder and brake booster, still the same.

Low speed like when ya slowly pull away and it gives a squeal yeah? like the disc pads are sticking....

It's cheap to check yaself before ya go throwing money at it like an idiot (points to self).

Jack.

Would dry ice work for this like peeps use for the sound deadener? Just a thought, could be a lil less messy.

Jack.

If you had smoke, you burnt something out and/or have a short. Check ya wiring harness hasn't got hot and melted a few wires together.

Best of luck.

Jack.

Mmmmmmm....... so neat and tidy. Love ya work.

Jack.

Pity thats not a 2 door corty P100 or you could run that side exhaust on the street..... hehe.

Sounds like me mates XG ute, runs headers, Cat, and ummmm....... thats it....... lol

Have fun at the track.

Jack.

Sweeet job man, that sounds lovely. Hope she tears balls off the strip.

Jack.

I saw a cool fix for this, drill a hole in the back of the guage, put a hose barb in,  chuck on some vaccuum hose,run to ya heater, and put a fitting in your plastic cowling on ya heater box, and hook her up. (be careful not to drill into something you shouldn't).

Then you can demist ya guages if they fog up.

Newer guages are completely sealed and don't fog.

Jack.

There should be 2 numbers and a dash between em on the gear , divide the second number into the first and thats ya gear ratio.

42-15  = 42 divided by 15 = 2.8 ratio

You probably know that, but someone will find that handy.

It will be faster than the Polo.... just ram it before ya drag.... hehehe.

Best of luck mate.

Jack.

ahhhhh, lovely Bear. I haven't seen a pre crossy in years. Last one was in my brothers XB pano, his first car.

Jack.

Thats a nice Motor combo ya got ando,  you got it sussed.

Diff gears, I'd be using something a lil taller with a top loader for ya rallye drive. Otherwise she be screaming and drinking like a fish if it has street gearing.... 4.11.

I found the 3.45 in my ute good as a combo for both, but I got a 5th gear. So in yours, somewhere around 2.73 or low 3's.

Should keep ya ... cough, cough...." fuel economy "resonable....... hehe

Jack.

I agree with Thom, power antennae. The first ones you are right power, acc power and earth.

Jack.

Moisture in the air........ or do you have the heaters on?

Thats all I got.

Jack.

Mmmmmmmmm..... get in Ma Ute!!!!

Jack.

Good shit Clevo , Go the 302! Love a nice looking 5L. Hope ya doing well down there and didn't get too flooded last week. 120mm here in 6 hours.... spare ute almost floated away.... hehe.

Jack.

Me and me mate were comparing them the other day and came to the conclusion that the aftermarket ones don't use silver to coat the reflective surfaced in the headlight like that used to.

If you look closely at an aftermarket headlight and a genuine Ford one, the aftermarket reflector is poor quality. More silver that highly reflective finish.

There is also a difference in the glass as stated above and the 'focus' of the beam is not as good as a result.

Oh, by the way  mate... ya ute looks flash after the paint job..... lovely.

Jack.

Must be one of the change over to XH motors Soarer, my Outback utes are both 95 XG utes and I have V belt on the alternator not serpentine belt.

Interesting.

Jack.

Unfortunately Kiwi, they are Exchange units and they wouldn't let me pay extra to keep the old ones, they go back to be remanufactured.

Brakes have been replaced........ Everything, just gotta fine tune em and should be apples.

Cheers for the replys.

Jack.

What type of coil did you replace the original with?  If you are trying a round oil filled type to replace the factory one..... won't work and ya ruined ya plug.

Green with red is usually for the positive side of the coil. Thats justa guess for now.

Pictures help heaps. load one up.

Jack.

BCM...... ECU...... they all taste like chicken to me.................... but ya get my drift. =) . That parts car will come in very handy.

Jack.

Heya Ben =) , you will have the triggers for the central locking from the ECU, all you need is motors in the doors for them to trigger the locks and to run the central locking wiring to the doors.

Basically, you need the whole harness from the BA everything from the back of the cab , forward.

Hope that helps. Jack.

Heya Polson,

Mate, I would be checking the trueness of the axle housings if they were true or not after a shunt like that.

The LSD's can't really be checked externally besides checking for play and bad noises, everything happens in the centre and it and the axles should come out and be checked for wear. I would replace the axle bearings and re-shim the centre before it went in if you want it nice and tight.

Sorry, but there is really not an easy way to see if it's in good condition from the outside.

Jack.

Nice work man, that HQ get off the lights a lil early, or just quick outta the box?

Jack.

Cheers mate, just ordered some for the ute. Take that slop right out, Thanks again.

Jack.

Mmmmmmm........ looks great Clevo120Y. Shiney...... hope ya pull some serious numbers =) .

Jack.