Jump to content
Server maintenance Read more... ×

Banno

Members
  • Content Count

    633
  • Joined

  • Last visited

2 Followers

About Banno

  • Rank
    Advanced Member

Recent Profile Visitors

5,207 profile views
  1. Banno

    XF DIFF RATIO

    Thought you get bored of the 2.53 with Eshays in Kia Rio’s beating you at the lights! Sent from my iPhone using Tapatalk
  2. Thanks mate Sent from my iPhone using Tapatalk
  3. Hi Guys, The selector shaft seal on a BW-40 auto how is that removed for replacement? Sent from my iPhone using Tapatalk
  4. Banno

    It's official: LPG is now dying off

    My ute runs both lpg and petrol but does run better on gas as that what it was set up for. I am up in Brisbane and I went to fill gas tonight at Greenslopes and that servo had the pumps out. Ended up driving over to east Brisbane to fill up which had gas otherwise it would have to drive 15-20 mins again to another servo that has gas. Be lucky any servos in qld or northern nsw have any servos with lpg in 5 years. Reason for retiring the ute shortly for a new car this year. Sent from my iPhone using Tapatalk
  5. Banno

    Unleaded XF EFi - won't start

    Check fuel regulator. Had mine years ago fail and was pumping extra fuel and made it run rich and rough etc. Pulled the Vacuum line off and was damp with petrol and smell. Took fuel reg off and petrol leaked out of the vacuum end of reg. Sent from my iPhone using Tapatalk
  6. Banno

    V8 into 6

    Fairlane/LTD rear doors don’t fit on sedans either. Sent from my iPhone using Tapatalk
  7. Banno

    V8 into 6

    Dean beat me to it. Best of luck with build mate. Sent from my iPhone using Tapatalk
  8. Banno

    V8 into 6

    Hi Sacko7 welcome to Ozfalcon. You will definitely get your answer here. NA to NC fairlane diff will fit too plus it be most likely LSD with ratio 3.27 just have to use the tailshaft from a eb falcon as it be correct length. Do you know what ratio you looking at or type of driving - cruising or street performance. The only thing at moment I can think of needing swapping is front springs to v8 (rear springs are same between 6 and 8), gearbox cross member, t-bar auto cause linkages are different between 6 and 8, exhaust system and engine mounts of course. Sent from my iPhone using Tapatalk
  9. Banno

    Ford xe efi vacuum hose diagram

    Thank you very much. That helps a lot. Sent from my iPhone using Tapatalk
  10. Banno

    Ford xe efi vacuum hose diagram

    Thanks mate. I don’t have Facebook unfortunately. Sent from my iPhone using Tapatalk
  11. Banno

    Ford xe efi vacuum hose diagram

    Thanks guys. There is info on the xf efi but very little on the xe system on the internet. Just looking for the hose set up on the the thermo switches on the Metal H pipe work under manifold that run the heater hoses as well. Sent from my iPhone using Tapatalk
  12. Long shot but would anyone have diagram of the vacuum hose set up for XE efi system? Cheers Sent from my iPhone using Tapatalk
  13. Banno

    TFI and est distributor

    Can a EST dizzy be converted into a TFI dizzy or both will operate the same even with a TFI module connected to a est dizzy but at different position in engine block? Sent from my iPhone using Tapatalk
  14. Banno

    Mystery rear main seal size

    Okay a 83DA crank won’t fit in as it is a different size and wouldn’t fit in a 86DA. What are the part numbers on the rear seals that you bought Sent from my iPhone using Tapatalk
  15. Banno

    Mystery rear main seal size

    Check the block code under the intake manifold. That tell you what block you actually have incase motor has been swapped out. For a late xf it should be 86DA or 87DA. 83DA block would be rope seal and 84DA be the two piece seal Sent from my iPhone using Tapatalk
×