XFtoXE

Hi all I have a quick question. " is the xf pedal box different than xd and xethanks

Thanks Deankdx

After some suggestions for spark plugs in a 302c Dynotec stage 3 cam, MSD ignition. RPM edelbrock. currently using bosch HR9BC+ but they are fowling up. Thanks

Hello. Does any one have a wiring diagram for a engine stand Cheers Sent from my SM-G930F using Tapatalk

Thanks for the info, but the dizzy is not the problem. Basically I'm after a wiring diagram for a engine stand. The gauges I need tacho, temp, pressure, starter, alternator? To run in a cam. Do I need a alternator? Most diagrams I find online dont have one. Thanks Sent from my SM-G930F using Tapatalk

MSD but why does it matter. Curious Sent from my SM-G930F using Tapatalk

Hey guys. Quick question. I'm replacing a rear seal rope to a rubber seal, but what do I do with this pin? Cheers Sent from my SM-G930F using Tapatalk

Thanks mate Sent from my SM-G930F using Tapatalk

Hey guys I had a problem starting up a 302 after it had been sitting for a while. Not sure how long, but was told it had new lifters and heads had been remanufactured. So after putting it on a engine stand and starting it up, it would only run for about 2 minutes and then stall. After pulling it apart and not finding any thing wrong until I pulled out the lifters all were good except one which is stuffed. Any answers why this would happen will be appreciated Cheers Sent from my SM-G930F using Tapatalk

What I have found since pulling it apart is 020 bore. New timing gear. Standard iron heads ported. RPM air gap manifold ported. extractors 4 into 1. Sound like a v8 mainly with a bit of extra go Sent from my SM-G930F using Tapatalk

Hey guys Just thought I'd show you the cam. Spot on with the comments Any recommendations for a new cam? Nothing to extreme and reasonable priced Sent from my SM-G930F using Tapatalk

I didn't know much about this engine when I bought it except what they told me. But some previous replies jogged my memory. First thing I did was to pressure test the cylinders. So all going well until number 6 (the lifter in question)and no pressure at all. I did this twice and no pressure thinking that the gauge is not working, third time I tried it came up 140 psi and thought no more about it. So is it possible the lobe was damaged at this time. Sent from my SM-G930F using Tapatalk

Yea I think I new that just needed to hear from someone else Thanks guys

Hey guys. Does anybody have a bellhousing off a 6 cyl to fit a C4 trans they would like to part with or know where i could get one Thanks

Hello all Quick question. Does a XD XE steering column interior trim fit on a XF steering column? Cheers peter

Thanks Gerg

Hi all. I have a quick question. What type of grease do you put between the module and the distributor, and why? cheers

Hi all. Can anyone tell me if C4 internals fit into a C10 case?????? cheers

This sounds good any body used one? https://www.ebay.com.au/itm/ELECTRONIC-DISTRIBUTOR-FITS-FORD-FALCON-XE-6-CYL-3-3L-4-1L-1982-1984-DISSY/223241696922?

Mine is a solid state ignition which would be the pre EST distributor Is this the part I need? By the way thanks for the help

I think my jigger only has 2 wires. I obviously dont know much distributors hall effect jiggers and now pips. I took it out and dismantled it and their is a lot of play in the shaft so its off to the wreckers. Choke is good thanks chestnut

Yea changed the coil as I thought that would be the problem But still the same as soon as it reaches 90 degrees (on my gauge) it stops dead and wont start again. So I will pull the dizzy and check out sparky dave idea The hall effect sensors is that the stator?

Thanks deankdx. This could be the reason my ute dies as soon as it warms up.

Thanks jca4 I have since bought a second hand one which works ok but would still like to rebuild the original one. So I will check some brake shops and let you know how i go.

Hello all Does anyone know where I can buy a brake booster repair kit VH395 for a XE. 2 diaphragms and 2 seals. Part numbers: VH2579 VH2580 VH2581 VH2582 Cheers.